A dubplate is a custom lathe cut vinyl record made one at a time in real time. There’s no pressing plant or molds involved—your audio is carved directly into a plastic disc using a diamond stylus. They’re perfect for DJs, selectors, limited releases, collectors, short runs, or one-off gifts.

How do bulk discounts work?

Bulk discounts are automatically applied at checkout—no code needed. The discount applies to qualifying items in a single order before shipping and taxes.

What are the bulk discount tiers?

10+ items get 10% off, 20+ get 15% off, 30+ get 20% off, and 50+ get 25% off.

Do I need a coupon code for bulk discounts?

No. Discounts are calculated and applied automatically at checkout.

Does the discount apply to shipping or taxes?

No. The discount applies only to qualifying items in the order subtotal before shipping and taxes.

What does the runtime shown in the table mean?

The runtime in the table is the maximum total minutes of audio for that format and speed.

What audio format should I send?

Send WAV files, 24-bit preferred (16-bit is OK), 44.1 kHz or higher. Do not send MP3s. Upload two files named Artist_SideA.wav and Artist_SideB.wav.

Should I limit my audio before sending?

Avoid brickwall limiting. Pre-limited mixes are acceptable, but dynamic mixes cut louder and cleaner.

How should I handle bass and low-end for vinyl?

Center all bass below about 150 Hz to 100% mono with a correlation of +1.0. Low end can be monoed in pre-mastering if needed.

What should I know about stereo imaging and phase?

Keep stereo correlation positive (above 0) between 150 Hz and 4 kHz to avoid cancellations. Above 10 kHz, very wide stereo can cause splash—use with care. Always check mixes in mono.

How should I control sibilance for vinyl?

Control harsh S sounds by de-essing in the mix. We will address sibilance during pre-mastering where possible.

No. Do not clip. Square-wave distortion is amplified on vinyl and is hard on the cutting head.

Should I boost highs for vinyl?

Avoid heavy boosts above 10 kHz. Content above 15 kHz can distort or splash during cutting.

How long can each side of a lathe cut record be?

Longer sides require lower volume, resulting in more surface noise. Inner grooves lose high-end and distort more on bright or loud material. Typical max side lengths: 7″ up to 4 min; 10″ 6–10 min (45/33⅓); 12″ 8–15 min (45/33⅓). Put detailed tracks first and quieter tracks last.

What reference level do you use for mastering?

All audio is aligned to DIN 45 541 calibration: 0 dB reference equals a 1 kHz tone at 5 cm/s RMS lateral velocity. For premaster files, this is roughly −20 dBFS RMS.

How do I upload my audio and artwork files?

We use an uploader built directly into the cart. While placing your order, you can click or drop your files using the Hot Pink button.

What file types and sizes are accepted?

Accepted types: WAV or AIFF for audio; PNG, PDF, JPEG/JPG for artwork; ZIP for bundles. Max total size is 200 MB. Use one file per side—Side A and Side B. If files are too large, send via WeTransfer to info@lathecutvinylrecords.com.

What is the production turnaround time?

Standard turnaround is about 2 weeks once we receive your audio and artwork.

How long does shipping take?

U.S. orders usually arrive within 3–5 business days after shipping. International orders typically arrive within 7–21 business days depending on location and customs.

Can I get a tracking number?

Yes. You will receive a tracking number once your order ships.

Do you offer rush options?

Rush options may be available. Please contact us before ordering to confirm.

What is your return policy?

Due to the custom nature of lathe cut vinyl records, all sales are final. Each record is handmade to your order and cannot be resold or reused, so we do not accept returns or exchanges.

What if there’s a problem with my order?

If your order arrives damaged or has a playback issue, contact us at info@lathecutvinylrecords.com and we’ll make it right.

FAQ

What is a DUBPLATE?

A dubplate, or lathe-cut vinyl record, is made one at a time in real time. Each groove is physically cut into a durable PETG disc using a diamond stylus, with mono and stereo formats available.

How To Prepare Side A + Side B

Submit one completed audio file for Side A and one completed audio file for Side B. Your files should already contain the songs in the exact order you want them to play.

Step 1

Arrange Your Songs

Place the songs in the exact order you want them to play and create one continuous Side A file and one continuous Side B file.

What is a program?
Side A + Side B together are one program. Your quantity is the number of identical copies of that program.

If you want different audio on another record, that is a different program and requires a separate order / checkout.

Example: Quantity 10 = 10 copies of the same Side A + Side B. It does not mean 10 records with different audio.

Multiple songs? Leave approximately 2 seconds of silence between songs so we can identify the track changes and create the physical track bands.

Runtime: Each side must stay within the maximum runtime published for the record format you purchase. Audio exceeding that limit may be faded at the maximum runtime, and remaining audio will not be cut.

Step 2

Export Side A + Side B

Export the completed sides as:
Side A.wav
Side B.wav

WAV or AIFF only. 44.1 kHz – 192 kHz. 24-bit preferred. 16-bit accepted.

Your submitted Side A and Side B files are your approved production files. We manufacture using the songs, versions, sequencing, and side assignments contained in those files.

If the submitted files are usable for the product purchased, we may proceed with production without contacting you for additional confirmation.

No MP3. Do not convert compressed files to a higher sample rate or bit depth. Export at the project's original resolution whenever possible.

Step 3

Upload Both Files

Upload both completed audio files at checkout and name them clearly:

Artist_SideA.wav
Artist_SideB.wav

Required: Files must be fully downloadable. Streaming and social-media links are not accepted.

Large files may be sent by WeTransfer after checkout.

Track Gaps & PQ Sheets

If a side contains multiple songs, leave approximately 2 seconds of silence between songs. We use those silent sections to identify the track changes and create the physical track bands while cutting the record.

The silence in your audio is a production guide. The physical separation on the finished record is created by the lathe during cutting and may vary. It is not guaranteed to match the exact duration of silence in your digital file.

PQ Sheets Are Welcome

A PQ Sheet is not required for a standard order when your completed Side A and Side B files already contain clear gaps between songs. We use those silent sections to locate the track changes.

Exact track-band timing or placement is not guaranteed without a PQ Sheet.

Exact Placement Requires A PQ Sheet

If exact track starts, gap locations, timing, or track-band placement matter, submit a PQ Sheet listing the song order, start time, end time, and requested gap locations for Side A and Side B.

Your Files Set The Order

Your completed Side A and Side B files determine the song order and side assignment.

We do not rearrange songs contained in customer-submitted completed side files.

Track Limit

Maximum 4 track gaps / 5 individual tracks per side.

If you need more tracks, combine material into a continuous program.

Prepare Your Audio For Vinyl

You do not need to create a special loudness master for us. We do not require a specific LUFS target. Send the best-quality version of your mix at its original resolution. Better source material gives us more room to produce a clean, stable lathe cut.

Dynamics & Limiting

Avoid clipping and aggressive brickwall limiting. Dynamic mixes with healthy crest factor generally preserve more transient information and give us more cutting headroom.

Bass

For stereo cuts, low bass should remain reasonably mono-compatible. Excessive stereo information in the low frequencies can create groove and playback problems.

Stereo Width

Avoid excessive stereo width and phase problems. Check your stereo mix in mono before submission. Stereo files are cut in stereo and mono files are cut in mono.

High Frequencies

Control harsh highs, excessive vocal sibilance, feedback, and sustained high-frequency energy. These signals can be difficult to reproduce safely and cleanly on vinyl.

Longer Sides

Longer sides require tighter groove spacing and generally reduce the available cutting level. Bass-heavy material becomes increasingly important as playing time increases.

Song Order

Louder, brighter, or more aggressive material generally performs better earlier in the side. When possible, place less demanding material closer to the end of the side.

Free Vinyl Premastering Is Included With Every Record. Once your completed Side A and Side B programs are submitted, we optimize each full side for the lathe-cutting process.

Included vinyl premastering may involve adjustments to overall cutting level, groove spacing, fades, filtering, stereo bass management, de-essing, and other technical parameters required for reliable cutting and playback.

Vinyl premastering is applied to the entire completed side as one continuous program, not independently to every song. The loudest, brightest, most distorted, or bass-heaviest song can determine the maximum safe cutting level for the entire side.

Every mix is different. Sub-bass, vocal sibilance, stereo information, clipping, limiting, distortion, crest factor, frequency content, and playing time all affect how a record can be cut.

In many cases, sending us a more dynamic mix without aggressive final limiting gives us a better source for vinyl than attempting to repair an already over-limited master.

Need Us To Sequence Or Master Your Songs?

If you only have individual songs instead of completed Side A and Side B files, purchase Side Sequencing or Vinyl Mastering.

When we sequence individual songs for you, we build the completed Side A and Side B files and send those files back to you for approval before cutting.

Standard orders where you submit your own completed Side A and Side B files do not receive an additional sequencing approval. Your submitted files are treated as your approved sequence.

Side Sequencing

Already-mastered individual songs can be assembled into completed Side A and Side B programs with approximately 2 seconds between songs.

Vinyl Mastering

Vinyl mastering is available at $5 per song. If your individual stereo mixes need mastering, we can master the songs before assembling the completed sides.

Sending Large Files

If your files exceed the checkout upload limit, use WeTransfer and include your order number.

Send Files To

info@lathecutvinylrecords.com

Include With Transfer

Include your order number, artist name, and project name. Clearly identify Side A, Side B, artwork, or PQ sheets.

Other Services

Dropbox or another fully downloadable direct-transfer service is accepted as long as we do not need to request access or create an account.

Files must be immediately downloadable. Do not send links that require us to request permission, sign in, or create an account.

Open WeTransfer

Checkout Uploads

The checkout uploader includes three upload slots.

File 1 — Side A

Title_SideA.wav
WAV or AIFF

File 2 — Side B

Title_SideB.wav
WAV or AIFF

File 3 — Artwork / PQ Sheet

Upload artwork, a PQ Sheet, or a ZIP containing additional production materials when applicable.

How Programs Connect To Shipping & Handling

Each Side A + Side B program is its own production order. We receive and check the files, vinyl-premaster the completed sides, prepare the program for cutting, manufacture the records, package them, and fulfill that order.

Our standard $10 USPS Media Mail shipping/handling charge is per mailer, per program/order.

Without Jackets

Up to 10 identical records per $10 mailer.

With Jackets

Up to 5 identical records per $10 mailer.

If you order another record with different audio, that is a different program and requires a separate checkout with its own shipping/handling.

Multiple orders going to the same customer may be combined for shipment when possible. Depending on the size of the orders, they may ship together in one larger package or as multiple packages. We consolidate shipments when practical, but each program/order still requires its own production preparation, handling, and fulfillment.

ONE A+B PROGRAM = ONE ORDER
QUANTITY = IDENTICAL COPIES OF THAT PROGRAM
$10 MEDIA MAIL = PER MAILER, PER PROGRAM/ORDER

Quick Submission Rules

Program: Side A + Side B = one program.

Quantity: The number of identical copies of that program.

Different Audio: A different program requires a separate checkout.

Shipping: $10 Media Mail per mailer/program — up to 10 records without jackets or 5 records with jackets.

Audio: One completed Side A + one completed Side B.

Approval: Your submitted completed sides are your approved production files.

Format: WAV or AIFF.

Resolution: 44.1–192 kHz. 24-bit preferred; 16-bit accepted.

Spacing: Approximately 2 seconds between songs.

Track Limit: Maximum 4 gaps / 5 tracks per side.

Exact Gaps: Submit a PQ Sheet.

Basic Vinyl Mixing Notes

Avoid clipping and aggressive limiting.

Keep low bass reasonably mono-compatible.

Avoid excessive stereo width and phase problems.

Control harsh highs and excessive sibilance.

Preserve reasonable crest factor and dynamics.

Longer sides require tighter groove spacing.

Brighter or more aggressive songs generally perform better earlier in the side.

Harsh Noise Music & Unsafe Audio Content

Audio containing harsh noise, continuous full-spectrum noise, excessive distortion, sustained high-frequency energy, feedback, brickwall limiting, little to no crest factor, clipping, or other extreme sonic characteristics may be considered unsafe for the lathe-cutting process.

If submitted audio is determined to pose a risk to the cutter head, stylus, or cutting system, we reserve the right to reduce the cutting level, apply filtering or other mastering adjustments, shorten the program, or decline the project. Our primary responsibility is protecting the cutting system while producing the highest-quality record possible.

Cutting system calibrated to DIN 45 541 reference standards. Vinyl premastering, vinyl mastering, and cutting optimization are handled in-house.

By submitting audio, you confirm that you have the legal right to reproduce the submitted material and that your Side A and Side B files contain the correct songs, versions, order, and side assignments for production.

Artwork Requirements

Preparing artwork for a lathe-cut record does not need to be complicated. Use the guides below for our standard center labels, jackets and CNC engraving. We handle the final sizing and production preparation.

Center Labels

7" records use 3.5" center-label artwork.
12" records use 4" center-label artwork.

Submit Side A and Side B artwork separately. Do not add the .313" center hole. We add the center hole during production.

Jacket Artwork

7" jackets: 7" × 7" front and back artwork. Our 7" package uses two printed cardstock panels inside a clear slip-on outer sleeve.

12" jackets: 12" × 12" front and back artwork applied to a tip-on jacket with a spine.

Jacketed Record Shipping: Vinyl records with jackets are packed at a maximum of 5 records per vinyl mailer.

No Bleed Required

You do not need to add bleed. Your artwork does not have to be built to commercial print-shop specifications or fit our dimensions perfectly. We size, stretch, crop or adjust the artwork as needed to fit our production format.

Keep Important Artwork Safe

Because artwork may need minor sizing or cropping, keep important text, logos, faces and other critical design elements away from the extreme edges. 300 DPI PNG or PDF files are preferred.

Custom Artwork & Specialty Options

Have something different in mind? We can work with picture discs, UV printing, CNC engraving, specialty materials, mirror or reflective finishes, holographic effects, custom shapes, multi-hole designs, zoetrope artwork, inserts, lyric sheets and specialty packaging.

Multiple processes can be combined. Send us your concept and we can determine the best way to manufacture it.

CENTER LABEL ARTWORK

SIDE A & SIDE B

← 3.5" →

● 3.5" diameter

● Transparent background

● Do not add the .313" center hole

● 300 DPI

● PNG or PDF

7" JACKET ARTWORK

FRONT & BACK

← 7" →

● 7" × 7"

● Front & back artwork

● 300 DPI

● PNG or PDF

● Slip-in jacket inside clear outer sleeve

CENTER LABEL ARTWORK

SIDE A & SIDE B

← 4" →

● 4" diameter

● Transparent background

● Do not add the .313" center hole

● 300 DPI

● PNG or PDF

12" JACKET ARTWORK

FRONT & BACK

← 12" →

● 12" × 12"

● Front & back artwork

● 300 DPI

● PNG or PDF

● White or black jacket with spine

● Tip-on front & back artwork

CNC ENGRAVING ARTWORK

SINGLE-SIDED ONLY

← 3.5" →

● 3.5" diameter artwork area

● Transparent background

● Do not add the .313" center hole

● Black & white artwork works best

● Bold, clean line artwork works best

● 300 DPI

● PNG or PDF preferred

How CNC engraving works: We import your artwork and generate the engraving lines from your image. Simple, high-contrast artwork produces the cleanest engraving.

Production & Delivery

All records are individually cut and assembled in-house. Production begins once the materials required for your order are received.

Production & Shipping

How long does production & delivery take?

All records are individually cut and assembled in-house. Production begins once the required audio, artwork, order details, and approvals for your project have been received.

Standard production: typically 3–14 business days.
Single one-off records: may ship sooner depending on current production volume and project requirements.
Larger runs: may require additional production time depending on quantity, artwork, complexity, and current scheduling.
Lathe-specific vinyl mastering: optional mastering may add approximately 1–3 business days depending on sequencing, revisions, and project requirements.

Production time and shipping time are separate. Shipping transit begins after production is complete. Faster shipping does not shorten production time unless rush production has also been separately approved.

Shipping & Returns

Shipping methods and rates vary by product. Custom records, record blanks, diamond cutting styli, artwork, and specialty products may use different shipping services.

Custom Record Shipping

Qualifying U.S. custom record orders normally ship via USPS Media Mail.

Standard Records $10 shipping & handling per mailer — up to 10 records without jackets.

Records With Jackets $10 shipping & handling per mailer — up to 5 jacketed records per mailer.

Orders requiring more than one mailer are charged $10 for each required mailer.

Shipping time begins after production is complete. Tracking is provided when available after your order ships.

Other Products

Record blanks, diamond cutting styli, artwork, supplies, and specialty products may use different shipping methods and rates.

Available shipping options are shown on the applicable product page, at checkout, or on your custom invoice.

Eligible products may also be available for international shipping.

Returns

Because many of our products are custom-made, customer-specific, specialty products, or professional tools, all sales are final except where otherwise required by law.

If your order arrives damaged or you believe it has a manufacturing defect, contact info@lathecutvinylrecords.com within 7 days of delivery.

Important Notes

Production time and shipping time are separate. Faster shipping does not shorten production time unless rush production has also been approved. Customer-supplied shipping labels may be accepted for eligible orders. Large, bulk, and specialty orders may require custom packaging or shipping arrangements.

Lathe Cut Vinyl Records

Q&A

Ordering a custom record should not be confusing. These answers cover ordering, audio preparation, track limits, artwork, specialty records, production, shipping, and Rush service.

YOUR AUDIO MUST BE READY BEFORE YOU ORDER

Please do not check out while you are still waiting for, recording, mixing, mastering, or collecting your audio. Upload your completed files at checkout or have them ready to send immediately by WeTransfer.

01

Ordering Custom Records

One record program, quantities, discounts, and separate projects.

Can I put different audio on each record in my order?

No. Quantity means identical copies of the same record.

We call the complete audio for one record a program. Side A + Side B together are one program.

If you order 10 copies, all 10 records contain the same Side A and Side B program.

ONE SIDE A + SIDE B PROGRAM = ONE ORDER
QUANTITY = IDENTICAL COPIES OF THAT PROGRAM

If you want records containing different audio, each different program must be ordered separately.

What do you mean by an audio “program”?

A program is the complete audio contained on one record. Side A + Side B together make one program.

A side can contain one song or several songs. That does not create additional programs. It is still one record program.

When you increase the quantity, we manufacture additional identical copies of that same program.

I need several different custom records. How do I order them?

Complete a separate website order for each different record.

Finish and pay for the first record, then return to the website and place the next order.

Each unique record receives its own order number, audio submission, production preparation, handling, and fulfillment.

Example:
10 identical copies of one album = 1 order.
10 records containing 10 different programs = 10 separate orders.

Different audio does not automatically require a custom quote. If the size, runtime, quantity, material, and options you need are available on the website, simply order each different record separately.

Can I put several different records into one shopping cart?

No. Use one completed checkout per unique record program.

This keeps the audio, artwork, quantity, production setup, shipping/handling, and fulfillment connected to the correct order.

Do not purchase one large quantity and then send several different Side A / Side B programs for us to divide between the records.

How do quantity discounts work?

Quantity discounts apply to identical copies of the same record program.

10 Copies 5% OFF

20 Copies 10% OFF

30+ Copies 15% OFF

Different records cannot be combined to reach a larger quantity tier.

For example, three different records with 10 copies of each are three separate 10-copy orders — not one 30-copy order.

What is the $10 Media Mail shipping / handling charge?

Our standard checkout uses a $10 USPS Media Mail shipping/handling charge per mailer.

A standard record mailer holds up to:

10 records without jackets
5 records with jackets

Orders requiring additional mailers are charged accordingly.

The charge is not simply the cost printed on a USPS postage label. It also helps cover production handling, packaging, shipping preparation, and fulfillment.

Multiple completed orders going to the same customer and address may sometimes be physically consolidated into a larger shipping box when practical. Each unique record is still its own production order.

02

Audio & File Preparation

Rights, formats, uploads, track gaps, PQ sheets, and production-ready audio.

Do I have to own the rights to the audio I submit?

Yes.

You must own the rights or have permission, licensing, or authorization to reproduce all audio submitted for vinyl production.

By submitting audio and placing an order, you confirm that you have the legal right to reproduce the material.

Purchasing a song, owning a digital copy, or having access to it through a streaming service does not by itself give you reproduction rights.

We do not use YouTube, Spotify, Apple Music, or other streaming links as production audio or as authorization to reproduce copyrighted music.

Does my audio need to be ready before I order?

Yes. Your audio must be ready when you order.

Do not place an order planning to send the audio several days or weeks later.

Your completed production audio should be uploaded during checkout or ready to send immediately by WeTransfer if the files are too large or your project requires multiple individual song files.

PLEASE DO NOT CHECK OUT UNTIL YOUR AUDIO IS READY.

Complete, usable production files should be received within 48 hours of checkout.

What audio format should I submit?

We prefer:

WAV or AIFF
44.1 kHz–192 kHz
24-bit preferred
16-bit accepted

Whenever possible, submit your original lossless master rather than a compressed audio file.

All I have is an MP3. Can I still make a record?

Yes. If the MP3 is truly your best available source, convert it to a 16-bit WAV before submitting it.

Converting an MP3 to WAV does not improve its sound quality or restore information removed during MP3 compression. It simply converts the file into the production format we need.

If an original WAV, AIFF, or other lossless master exists, please use that instead.

How should I send my files?

Our pink website uploader is the preferred method.

FILE 1 — SIDE A
Completed Side A WAV or AIFF.

FILE 2 — SIDE B
Completed Side B WAV or AIFF.

FILE 3 — ARTWORK / PQ
Place your labels, jacket artwork, PQ sheet, and related project files into one ZIP folder.

Use WeTransfer when your files are too large for the uploader or when you need to send multiple individual songs, multiple artwork files, or files for Side Sequencing / Vinyl Mastering.

Do not send Google Drive links.
We do not use file-sharing links that require us to sign in, request access, create an account, or wait for permission before downloading your files.

Production files need to be immediately downloadable when we receive them.

Should I send individual songs or completed Side A and Side B files?

For a standard order, please submit one completed Side A file and one completed Side B file.

Arrange your songs in the correct order and place approximately two seconds of silence wherever you want a track separation.

If you want us to assemble individual songs into Side A and Side B, purchase our Side Sequencing service.

Do I need a PQ sheet?

A PQ sheet is generally optional when you provide your own completed Side A and Side B files and the intended track gaps are clearly identifiable in the audio.

Submit a PQ sheet if exact song starts, endings, gap locations, or physical track-band placement matter to your project.

A PQ SHEET IS REQUIRED FOR MULTI-SONG SIDE SEQUENCING AND VINYL MASTERING PROJECTS.

If you send us a folder containing individual songs, we need the PQ sheet to tell us the correct song order, which songs belong on Side A and Side B, and the intended sequence.

We cannot determine your intended album sequence from a folder of individual song files.

How do track gaps work?

Leave approximately 2 seconds of silence wherever you want a track separation.

That silence gives us an identifiable location for the physical track band.

NO IDENTIFIABLE GAP = NO SEPARATE TRACK BAND

The digital silence is a production guide. The exact appearance and physical width of the space on the finished record may vary.

If a track location is not clearly identifiable in the audio, identify the exact location on a PQ sheet.

03

Tracks, Runtime & Audio Quality

How much music fits, track-band limits, and what makes a good cut.

How many tracks can I put on one record?

Our standard production limit is 5 identifiable tracks per side, or up to 10 tracks total on a two-sided record.

That means a maximum of 4 physical track gaps per side.

You can technically have more than 10 individual songs if some songs flow directly into one another and are treated as one continuous track section.

For example, two songs that play continuously with no identifiable gap between them can be treated as one track for physical track-band placement.

If you need more than five separately identifiable track bands on one side, contact us before ordering to see whether specialty cutting is currently available.

How much audio can I put on a record?

Runtime depends on the record size, RPM, and product you purchase.

Always follow the runtime listed on the product page you are ordering.

Longer sides require more cutting time and tighter groove spacing. The technical ability to fit additional audio does not mean that additional runtime is included in every product price.

Submitting audio longer than the runtime you purchased does not automatically upgrade your order to an extended-time or specialty cut.

What happens if my audio is longer than the product I purchased?

The runtime published on the product page is the runtime included with that product.

If submitted audio exceeds the purchased runtime, we may need to shorten or fade the program at the purchased maximum, or contact you if the project requires a different product or specialty service.

Please choose the correct product before ordering.

What kind of audio sounds best on a lathe-cut record?

Clean, dynamic audio generally gives us the most flexibility when cutting.

You do not need to create a special loudness master or hit a specific LUFS target for us.

Avoid unnecessary clipping, extreme limiting, or distortion unless those sounds are intentionally part of the music.

Dynamic Audio — Better Starting Point

Heavily Limited / Clipped

Our vinyl premaster can prepare your supplied program for cutting, but it cannot restore musical information already destroyed by clipping or excessive limiting.

Can you cut bass-heavy, loud, noisy, or experimental music?

Usually, yes.

Bass level, stereo bass information, high frequencies, sibilance, overall level, runtime, and program material all affect how a record needs to be cut.

We may make appropriate vinyl-premastering and cutting adjustments to produce a playable record.

Should I add fake vinyl crackle or surface noise to my master?

Only if you intentionally want that sound permanently included in your music.

Any crackle, hiss, distortion, noise, or vinyl simulation contained in your submitted audio becomes part of the program we cut.

For the cleanest result, send us the cleanest source available.

Will the record sound exactly like my digital file?

No physical record is identical to digital playback.

Groove spacing, runtime, cutting level, bass, high-frequency content, playback stylus, cartridge, turntable setup, and other physical variables affect vinyl playback.

Shorter sides generally allow more room for groove spacing and level. Longer sides require more audio to fit into the available cutting area.

04

Premastering, Sequencing & Mastering

These are three different parts of record production.

Is vinyl premastering included with my record?

Yes.

Basic vinyl premastering of your completed Side A / Side B program is included with our record production.

We treat each completed side as one continuous program and may make appropriate cutting adjustments such as overall level, filtering, stereo bass management, de-essing, fades, and other preparation needed for lathe cutting.

INCLUDED VINYL PREMASTERING IS NOT SONG-BY-SONG MUSIC MASTERING.

What is Side Sequencing?

Side Sequencing is for customers who have individual finished songs but have not assembled them into completed Side A and Side B files.

We arrange the supplied songs in the order shown on your PQ sheet and create the completed record sides.

Standard spacing is approximately two seconds between tracks unless your PQ sheet specifies something different.

A PQ sheet is required for multi-song Side Sequencing.

What is Vinyl Mastering?

Vinyl Mastering is for individual stereo mixes that need to be mastered before the final record sides are assembled.

This is separate from the free vinyl premastering applied to a completed Side A / Side B program.

Our standard Vinyl Mastering service is currently $5 per song.

For a multi-song mastering project, submit the individual song files and a PQ sheet showing song order and side assignment.

05

Specialty & Custom Records

Unusual grooves, playback formats, materials, and experimental projects.

Do you make specialty or unusual records?

Yes — when the service is currently available.

Depending on our equipment, materials, workload, and current product offerings, specialty projects may include:

Inside-out / inverse cuts
Locked grooves and repeating loops
DJ tools and Maxi-Single style cuts
Single-sided records
33⅓, 45, or specialty RPM projects
Half-speed cutting
Custom groove layouts
Unusual sizes or shapes
Experimental playback concepts

IF YOU DO NOT SEE THE OPTION LISTED ON OUR WEBSITE, CONTACT US BEFORE ORDERING.

Our ability to make something does not necessarily mean it is a standard product currently available for purchase.

Can I order a standard record and ask for a specialty cut afterward?

No.

Ordering a standard product does not automatically include unpurchased specialty cutting, additional runtime, different materials, unusual groove configurations, or other upgrades.

Notes, emails, artwork, file names, or audio submissions do not add products or specialty services to an order.

If your project requires something that is not currently listed, contact us before checkout.

Can you make picture discs, colored records, shapes, engraved records, or other unusual designs?

We work with a variety of physical-media processes depending on current materials and production availability.

These can include picture discs, colored materials, CNC engraving, shaped records, UV printing, specialty artwork, record postcards, liquid discs, zoetrope artwork, chocolate records, and other experimental formats.

Check the products currently listed on our website first.

If a material, color, size, artwork option, or specialty format is not listed, do not order a different product and assume we can substitute it afterward.

Contact us before ordering and we can tell you whether the specialty option is currently available.

Can I make my own artwork?

Absolutely.

DIY artwork is welcome. You can prepare your own labels, jackets, inserts, and other artwork as long as the files meet the requirements for the product you purchase.

Please review the artwork specifications on the applicable product page before submitting your files.

Can you design or develop a completely custom project for me?

Basic questions about whether an idea is possible are welcome.

If your project requires us to create or substantially modify artwork, build mockups, prepare complex files, prototype a concept, develop an unusual cutting format, or spend significant time developing the project, that work may require a design fee or custom quote.

Custom development is separate from simply ordering a standard custom-audio record from the website.

06

Production, Rush & Shipping

Production priority, deadlines, and getting your records to USPS.

How long does production take?

Production time depends on quantity, cutting time, artwork, materials, project complexity, and our current production queue.

Small standard orders can often move quickly, while larger or more involved projects naturally require additional production time.

Production time and carrier transit time are separate. Shipping time begins after your order is completed and transferred to the carrier.

I have an event or deadline. Should I order first and tell you afterward?

No. Contact us before ordering if the deadline is critical.

If your records are needed for a wedding, event, release, performance, birthday, corporate event, or other fixed date, tell us before placing the order.

We can tell you whether the timeline is realistic and whether Rush Production should be added.

What does Rush Production mean?

Rush Production moves your order to the front of our production line, ahead of standard-production orders.

Rush orders are prioritized in the order they are received.

$40 RUSH + MEDIA MAIL

$60 RUSH + PRIORITY MAIL

$120 RUSH + EXPRESS MAIL

RUSH = MOVE TO THE FRONT OF THE PRODUCTION LINE

Cutting and manufacturing still physically take time. Rush does not mean that a record is manufactured instantly.

The shipping method determines how the package travels after production. Priority Mail or Express Mail does not make the record itself faster to manufacture — Rush Production is what moves the order forward in our production queue.

Is Rush Production always available?

Rush capacity is limited because each Rush order is moved ahead of standard-production work.

Rush orders are handled first come, first served. Availability can depend on quantity, project complexity, current workload, and whether all production files are ready.

Rush cannot begin while we are waiting for missing audio, artwork, sequencing information, or other files required to manufacture the order.

Can I send you my own shipping label?

No customer-supplied shipping label is necessary.

Choose the appropriate shipping / Rush option through our website. Our current Rush options include Media Mail, Priority Mail, and Express Mail.

This keeps production priority, shipping, handling, and fulfillment connected to the correct order.

07

Before You Order

A few final rules that prevent production delays and misunderstandings.

Which specifications apply to my order?

The specifications on the product page you purchase govern that order.

This includes applicable runtime, RPM, track count, material, color, artwork options, cutting direction, quantity, and other product-specific requirements.

Please review the product page before checkout.

What if I submit something outside the product specifications?

Submitting files outside the listed specifications does not automatically purchase an upgrade or specialty service.

When appropriate, we may make normal production adjustments needed to conform supplied files to the product purchased.

These can include appropriate cutting-level adjustments, groove spacing, filtering, track-band placement, fades, or conforming runtime to the purchased product.

If the project requires an unpurchased specialty service or a substantially different product, that service is not automatically included because it was requested in an order note or submitted file.

I do not see the exact option I want. What should I do?

Contact us before ordering.

Specialty materials and unusual cutting options change depending on inventory, equipment, and production capacity.

If you do not see a particular color, size, material, specialty cut, artwork treatment, or other option listed for purchase, ask us whether it is currently available.

IF YOU SEE IT LISTED, YOU CAN ORDER IT.
IF YOU DO NOT SEE IT, ASK BEFORE ORDERING.

What are the most important things to know before checkout?

ONE SIDE A + SIDE B PROGRAM = ONE ORDER

QUANTITY = IDENTICAL COPIES OF THAT PROGRAM

YOUR AUDIO MUST BE READY BEFORE YOU ORDER

USE OUR PINK UPLOADER OR WETRANSFER

$10 STANDARD MEDIA MAIL SHIPPING / HANDLING = PER MAILER

RUSH = MOVE TO THE FRONT OF THE PRODUCTION LINE

Following these rules keeps your files connected to the correct order and allows us to move projects into production without unnecessary delays.

READY TO MAKE YOUR RECORD?

Choose the product that matches your size, RPM, runtime, quantity, and artwork requirements. Have your audio ready, complete checkout, and submit your production files with the order.

info@lathecutvinylrecords.com

Lathe Cut Vinyl Records

Custom lathe cut vinyl records, disc mastering, cutter supplies, artwork, and studio work from Grand Rapids, Michigan.

2557 Maguire Ave NE
Grand Rapids, MI 49525

12″ HALLOWEENGHOST RECORD

FULL GHOST SIZE

PLAYABLE AREA

45 RPM

7" Custom Vinyl Record — Lathe Cut

10" Custom Vinyl Record — Lathe Cut

12" Custom Vinyl Record — Lathe Cut

How To Prepare Side A + Side B

Step 1

Arrange Your Songs

Step 2

Export Side A + Side B

Step 3

Upload Both Files

Track Gaps & PQ Sheets

PQ Sheets Are Welcome

Exact Placement Requires A PQ Sheet

Your Files Set The Order

Track Limit

Prepare Your Audio For Vinyl

Dynamics & Limiting

Bass

Stereo Width

High Frequencies

Longer Sides

Song Order

Need Us To Sequence Or Master Your Songs?

Side Sequencing

Vinyl Mastering

Sending Large Files

Include With Transfer

Other Services

Checkout Uploads

File 1 — Side A

File 2 — Side B

File 3 — Artwork / PQ Sheet

How Programs Connect To Shipping & Handling

Without Jackets

With Jackets

Quick Submission Rules

Basic Vinyl Mixing Notes

Harsh Noise Music & Unsafe Audio Content

Artwork Requirements

Center Labels

Jacket Artwork

No Bleed Required

Keep Important Artwork Safe

Custom Artwork & Specialty Options

Production & Delivery

How long does production & delivery take?

Shipping & Returns

Custom Record Shipping

Other Products

Returns

Important Notes

Q&A

Ordering Custom Records

Audio & File Preparation

Tracks, Runtime & Audio Quality

Premastering, Sequencing & Mastering

Specialty & Custom Records

Production, Rush & Shipping

Before You Order

Lathe Cut Vinyl Records

Contact

Sitemap

Products

Services & Supplies

12″ Halloween Ghost Record – Custom Black Lathe Cut Vinyl

12″ HALLOWEEN
GHOST RECORD