A dubplate is a custom lathe cut vinyl record made one at a time in real time. There’s no pressing plant or molds involved—your audio is carved directly into a plastic disc using a diamond stylus. They’re perfect for DJs, selectors, limited releases, collectors, short runs, or one-off gifts.

How do bulk discounts work?

Bulk discounts are automatically applied at checkout—no code needed. The discount applies to qualifying items in a single order before shipping and taxes.

What are the bulk discount tiers?

10+ items get 10% off, 20+ get 15% off, 30+ get 20% off, and 50+ get 25% off.

Do I need a coupon code for bulk discounts?

No. Discounts are calculated and applied automatically at checkout.

Does the discount apply to shipping or taxes?

No. The discount applies only to qualifying items in the order subtotal before shipping and taxes.

What does the runtime shown in the table mean?

The runtime in the table is the maximum total minutes of audio for that format and speed.

What audio format should I send?

Send WAV files, 24-bit preferred (16-bit is OK), 44.1 kHz or higher. Do not send MP3s. Upload two files named Artist_SideA.wav and Artist_SideB.wav.

Should I limit my audio before sending?

Avoid brickwall limiting. Pre-limited mixes are acceptable, but dynamic mixes cut louder and cleaner.

How should I handle bass and low-end for vinyl?

Center all bass below about 150 Hz to 100% mono with a correlation of +1.0. Low end can be monoed in pre-mastering if needed.

What should I know about stereo imaging and phase?

Keep stereo correlation positive (above 0) between 150 Hz and 4 kHz to avoid cancellations. Above 10 kHz, very wide stereo can cause splash—use with care. Always check mixes in mono.

How should I control sibilance for vinyl?

Control harsh S sounds by de-essing in the mix. We will address sibilance during pre-mastering where possible.

No. Do not clip. Square-wave distortion is amplified on vinyl and is hard on the cutting head.

Should I boost highs for vinyl?

Avoid heavy boosts above 10 kHz. Content above 15 kHz can distort or splash during cutting.

How long can each side of a lathe cut record be?

Longer sides require lower volume, resulting in more surface noise. Inner grooves lose high-end and distort more on bright or loud material. Typical max side lengths: 7″ up to 4 min; 10″ 6–10 min (45/33⅓); 12″ 8–15 min (45/33⅓). Put detailed tracks first and quieter tracks last.

What reference level do you use for mastering?

All audio is aligned to DIN 45 541 calibration: 0 dB reference equals a 1 kHz tone at 5 cm/s RMS lateral velocity. For premaster files, this is roughly −20 dBFS RMS.

How do I upload my audio and artwork files?

We use an uploader built directly into the cart. While placing your order, you can click or drop your files using the Hot Pink button.

What file types and sizes are accepted?

Accepted types: WAV or AIFF for audio; PNG, PDF, JPEG/JPG for artwork; ZIP for bundles. Max total size is 200 MB. Use one file per side—Side A and Side B. If files are too large, send via WeTransfer to info@lathecutvinylrecords.com.

What is the production turnaround time?

Standard turnaround is about 2 weeks once we receive your audio and artwork.

How long does shipping take?

U.S. orders usually arrive within 3–5 business days after shipping. International orders typically arrive within 7–21 business days depending on location and customs.

Can I get a tracking number?

Yes. You will receive a tracking number once your order ships.

Do you offer rush options?

Rush options may be available. Please contact us before ordering to confirm.

What is your return policy?

Due to the custom nature of lathe cut vinyl records, all sales are final. Each record is handmade to your order and cannot be resold or reused, so we do not accept returns or exchanges.

What if there’s a problem with my order?

If your order arrives damaged or has a playback issue, contact us at info@lathecutvinylrecords.com and we’ll make it right.

News – Lathe Cut Vinyl Records

Why Vinyl Mastering Still Matters — Cutting vs. Producing at LatheCutVinylRecords.com

Discover why true vinyl mastering matters, how test lathe cuts save money, and why we cut every record on one calibrated lathe for perfect consistency. Read more...

RIAA vs IRIAA: The Science, History, and Calibration Behind Vinyl EQ

The RIAA and IRIAA curves are the hidden language of vinyl — one shapes the groove, the other restores it. From Decca 78s to modern digitally tuned lathes, these curves... Read more...

Lathe Meteorology: Environmental Control in Record Cutting

Lathe cutting is more than audio work — it’s environmental science. Lathe Meteorology breaks down how temperature, humidity, static, torque, and surface prep all interact to shape the sound and... Read more...

The Vinyl Pile: Taylor Sits Atop a 240-Ton Mountain of Vinyl Chloride

Taylor Swift’s vinyl sales created a 240-ton pile of PVC in one week — and that’s just one album. Her entire catalog equals the weight of six blue whales in... Read more...

Lathe Cut Vinyl Records vs. Pressed Vinyl: Setting the Record Straight

Lathe Cut Vinyl Records vs. Pressed Vinyl: Setting the Record Straight For decades, almost every article, press release, and search result about records has revolved around a single word: pressing.... Read more...

Lathe Cut Vinyl Record Postcard: Send Music Through the Mail

Lathe cut vinyl record postcards blend sound, art, and mail into a one-of-a-kind keepsake. Each is hand-cut, engraved, and mailable — perfect for messages, art, invites, or music. A simple... Read more...

Spindle Trick for Lathe Cut Vinyl Records: Perfect Labels

Use the spindle trick to apply perfectly centered labels on lathe cut vinyl records. Simple steps, clean finish—DIY or order stickers + records from us. Read more...

How-to-Submit-Artwork-for-Lathe-Cut-Vinyl-Records-Stickers-amp-Picture-Discs Lathe Cut Vinyl Records

How to Submit Artwork for Lathe Cut Vinyl Records, Stickers & Picture Discs

Learn how to submit artwork for lathe cut vinyl records, stickers, and picture discs. Simple size, format, and file tips for perfect results every time. Read more...

Lathe Cut Vinyl Records - How to Prepare Your Audio for Lathe Cut Vinyl Records (Mastering Guide)

Learn how to prepare your audio for clean, loud, hi-fi lathe-cut vinyl. Follow proper WAV format, mono lows, controlled highs, and smart sequencing for the best results. Read more...

What Are Lathe-Cut Vinyl Records? A Modern Guide to Dubplates & Direct-to-Disc Cutting

Lathe-cut vinyl records are individually made, stereo hi-fi discs cut directly from audio — not pressed in a factory. This modern take on dubplates combines classic sound system tradition with... Read more...

Country/Region

News